EpiMax 920

Solvent Based PU Hybrid Sealer

$445.00$830.00 inc GST

SKU: 11ECCC Categories: ,



EpiMax 920 Solvent Based PU Hybrid Sealer is a two pack fully cross-linking, non-yellowing protective finish for concrete floors. In particular, the system is suitable for floors in high-traffic areas and to provide good resistance to scuffs and staining. It also enhances the beauty of decorative concrete.

Floors protected with EpiMax 920 show reduced staining from materials such as oil, grease, food spills and many chemicals by producing a low maintenance, abrasion resistant, protective film that also exhibits good chemical resistance.

Since this product is solvent based as supplied, suitable precautions must be undertaken during the application process.



  • Clear or coloured
  • Good chemical resistance
  • Good work time
  • Fast dry time
  • UV resistant
  • Non-slip as required


Typical applications

  • Clear coat over flake floors
  • Polished concrete sealer
  • Industrial concrete sealer
  • Car park and garage floor protection


Typical properties

  • Mix ratio: 3 Part A to 1 Part B by volume
  • Wear resistance: Excellent
  • Volume solids: 55% (clear) – 70% (coloured)
  • Specific gravity: 0.98 (clear) – 1.25 (coloured)
  • Work time: 45 minutes at 25ºC
  • Touch dry: 2 – 3 hours approx. at 25ºC
  • Re-coat window: 6 – 12 hours at 25ºC
  • Foot traffic: 24 – 48 hours at 25ºC
  • Vehicle traffic: minimum 72 hours at 25ºC
  • Full solvent resistance: 7 days at 25ºC



Graphite Grey


Estimating data
4 – 6 sq.m/ltr approx. unsealed surfaces
6 – 8 sq.m/ltr approx. sealed surfaces

General surface preparation
Concrete should be at least 28 days old. Ensure it is clean, dry and free of additives, curing agents, oils, etc. Prepare as necessary by professional diamond grinding or captive blast cleaning as applicable to expose firmly held aggregate. Allow to dry if wet. Always confirm preparation adequacy. Surface profile should exceed CSP 2.

General application comments
Review the sub-floor area in advance so that a fixed volume of mixed material can be applied over a fixed area to ensure correct application rate. Select a slow speed (400 rpm) mechanical mixer and ensure thorough mixing.

Mix ratio
3 Part A to 1 Part B by volume. Mix until uniform. Apply with a short nap roller at an application rate of 4 – 6 m2 per litre on unsealed surfaces. Apply in two coats observing the re-coat window. Non-slip finishes can be achieved by suitable incorporation of EpiMax Aggregates.

Over-coating applications
If sealing freshly applied epoxy coatings, apply within re-coat window. If sealing old epoxy coatings, sand first and confirm adhesion in a test area.


EpiMax 920 Solvent Based PU Sealer Product and Safety Data Sheets



Epimax 920 Solvent Based PU Hybrid Sealer – EpiMax’s Website

Reviews (0)


There are no reviews yet.

Be the first to review “EpiMax 920”

Your email address will not be published. Required fields are marked *


Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.