SikaTop Armatec – 110 Epocem 8 Kg kit

Description

SikaTop Armatec-110 EpoCem is a cementitious epoxy resin compensated 3-component coating material with corrosion inhibitor, used as bonding primer and reinforcement corrosion protection. SikaTop® Armatec®-110 EpoCem® meets the requirement of EN 1504-7.

USES

• Suitable for control of anodic areas (Principle 11, method 11.1 EN 1504-9)
• Suitable in concrete repair as corrosion protection for reinforcement.
• Suitable as a bonding primer on concrete and mortar
• Suitable for Increasing cover in Low Cover Concrete rectification.

CHARACTERISTICS AND ADVANTAGES

• Contains EpoCem technology – improved bonding agent
• Extended open times for repair mortars
• Compatible with most Sika MonoTop® repair mortars
• Excellent adhesion to concrete and steel
• Contains corrosion inhibitor
• Certified for application under dynamic load conditions
• Good resistance to water and chloride penetration
• High shear strength
• Long pot life
• Easy to mix
• Can be brushed on or applied using spray gun
• 2mm cured material equivalent to approx. 50mm of Concrete

COLOUR
Mixed components dark grey
Component A: white liquid
Component B: colourless liquid
Component C: dark grey powder

PACKAGING
8 kg: A (0.457 kg) + B (1.143 kg) + C (6.4 kg)

MIXING
SikaTop Armatec-110 EpoCem can be mixed with a low speed (< 250 rpm) electric drill mixer.
Shake components A and B thoroughly before opening. Pour liquid components A and B into a suitable mixing vessel and mix for 30 seconds. While still mixing components A and B slowly add powder component C. Mix the three components together for a minimum 3 minutes, minimising addition of air. Leave to stand for 5–10 minutes until mixed coating material exhibits a brush-able, weakly dripping consistency.
DO NOT ADD WATER

APPLICATION
As reinforcement corrosion protection:
Apply first layer approx. 1 mm thick, using medium hard brush or spray gun to the cleaned reinforcement. Apply 2nd layer when the first coat is hard to the fingernail (~2–3 hours at +20 °C). Apply subsequent repair mortars wet on dry (so not to wipe off the protection layer).

As a bonding primer:
Apply using medium hard brush or spray gun to prepared substrate. To achieve good bond, SikaTop® Armatec®-110 EpoCem® must be applied well into the substrate, filling all pores (minimum layer thickness 0.5 mm). Apply subsequent repair mortars wet on wet Freshly applied SikaTop® Armatec®-110 EpoCem® must be protected against contamination and rain until application of the repair mortar.

Application under dynamic loading:
SikaTop® Armatec®-110 EpoCem® has been tested with the following Sika repair mortars and is certified for dynamic loading applications. Refer to separate sheets for further information.

Dry Spray Process:
Corrosion Protection: SikaTop® Armatec®-110 EpoCem®
Repair and overlay: Sika Gunite

Wet Spray Process:
Corrosion Protection and/or Bonding Primer: SikaTop® Armatec®-110 EpoCem®
Repair and Overlay: Sika MonoTop®-412NFG series

CURING TREATMENT
Protect the fresh mortar from rain while the material has not yet set.

SikaTop Armatec 110 Product and Safety Data Sheet Document Download

SikaTop® Armatec®-110 EpoCem® – Sika’s Website

Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.