Sika MonoTop 352NFG – 20kg

R3 Concrete repair mortar with corrosion inhibitor

$80.00 inc GST

Quantity:
SKU: E827B6 Categories: , , ,

Description

Description

Sika MonoTop®-352 NFG is a 1-component, polymer modified, fibre reinforced, low shrinkage light weight repair mortar with corrosion inhibitor meeting the requirement of class R3 of EN 1504-3.

 

USES

  • Suitable for restoration work (Principle 3, method 3.1 & 3.3 of EN 1504-9). Repair of spalling and damaged concrete in buildings, bridges, infrastructure and superstructure works.
  • Suitable for structural strengthening (principle 4, method 4.4 of EN 1504-9). Increasing the bearing capacity of the concrete structure by adding mortar.
  • Suitable for preserving or restoring passivity (principle 7, method 7.1 and 7.2 of EN 1504-9). Increasing cover with additional mortar and replacing contaminated or carbonated concrete.
  • Suitable for use as a repair mortar prior to application of Sikagard 62 and 63N

 

CHARACTERISTICS AND ADVANTAGES

  • Polymer modified for increased durability
  • Easy to apply and superior finishing
  • Suitable for hand and machine application
  • High Build can be applied up to 75 mm thick per application layer
  • Class R3 of EN 1504-3
  • Low density but still suitable for structural repair
  • Sulphate resistant
  • Very low shrinkage
  • Does not require a bonding primer even when manually applied
  • Contains corrosion inhibitor
  • Low permeability
  • Compatible with Sika® FerroGard® Sacrificial Anode System

 

COLOUR
Grey powder

 

PACKAGING
20 kg bags

 

MIXING
Sika MonoTop®-352 NFG can be mixed with a low speed (< 500 rpm) hand drill mixer or for machine application, using a force action mixer 2 to 3 bags or more at once depending the type and size of mixer. In small quantity, Sika MonoTop®-352 NFG can also be manually mixed.
Pour the recommended water in a suitable mixing container. While stirring slowly, add the powder to the water and mix thoroughly at least for 3 minutes during the mixing time adding additional water if necessary to the maximum specified amount and adjust to the required consistency.

 

APPLICATION
Bonding Primer:
On a well prepared and roughened substrate a bonding primer is generally not required for this product. When a bonding primer is required, refer to the System Information above for compatible Sika products and refer to the relevant Product Data Sheet for instructions. All small amount of Sika MonoTop®-352 NFG can also be mixed slightly wetter than normal and used as a scratch coat to promote adhesion of the repair mortar to the substrate. Any bonding primer shall be applied on a pre-wet substrate in saturated surface dry (SSD) condition and subsequent application of the repair mortar shall be applied wet on wet with the bonding primer.

Reinforcement Corrosion Protection:
Where a reinforcement coating is required the application of a repair mortar shall be applied wet on dry with the reinforcement corrosion protection. Refer to the System Information above for compatible Sika products and refer to the relevant Product Data Sheet for more detailed information about the reinforcement corrosion product.

Sika MonoTop®-352 NFG can be applied either manually using traditional techniques or mechanically using wet spray equipment. Thoroughly pre-wet the prepared substrate a recommended 2 hours before application. Keep the surface wet and maintain in SSD condition. The surface shall appear a dark matt appearance without glistening and surface pores and pits shall not contain water.

When manually applying first make a scratch coat by firmly scrapping the repair mortar over the substrate surface to form a thin layer and fill any pores or pits in the surface. Ensure the whole surface to be repaired is covered by the scratch coat. Build up layers from bottom to top by pressing mortar well into the repair area. The surface can be finished according to the requirements using a float while wet or with a relevant rough-cast tool as soon as the mortar has started to stiffen.

 

CURING TREATMENT
Protect the fresh mortar immediately from premature drying using an appropriate curing method e.g. curing compound, moist geotextile membrane, polythene sheet etc.

 

MonoTop 352 NFG Sika Data Sheets

 

 

Sika MonoTop®-352 NFG – Sika’s Website

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Sika MonoTop 352NFG – 20kg”

Your email address will not be published. Required fields are marked *

Disclaimer

Colour accuracy disclaimer: We have taken care to display the most accurate visuals of our products. However, we are not responsible for the colour accuracy of the device you are viewing our swatches on. These variations arise due to different computer monitors and devices (make, model and technology, as well as resolution, contrast and brightness control settings) in much the same way a scan will differ from an original image and a colour photocopy. Furthermore, coatings can exhibit variation in perceived colour depending on gloss level and application method. If you require a very specific colour match, please make your selection via actual swatches and colour boards available at our showroom.

Product Disclaimer: Ensure you read all product, technical and safety data sheets prior to application as liability falls on the applicator. All products must be applied in accordance with manufacturer’s recommended method.